With your 2022 Forest River Cherokee Wolf Pack 365Pack16 being 43-1/2' in length you'll most likely need the Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System w Touchpad and Remote - 6-Point Set # LC675817, but it's still best to measure to determine if the 6-point is needed over the 4-point.
To do this you'll need to just take your tape measure from the center of the landing gears to 1' behind the rear axle. if this measurement is less than 20' then you need the 4-point... view full answer...
This mounts inside the garage overlapping the doorway. You will need to measure the inside of your RV's garage width from wall to wall for which is best fit. The LaSalle Bristol CrossBreeze Adjustable Toy Hauler Screen, # 3441409775PBK is 97-3/4" wide. If you need a greater width, the LaSalle Bristol CrossBreeze Adjustable Toy Hauler Screen, # 3441409912PBK is is 99-18" wide. view full answer...
We do have the Dexter Electric Brake Kit part # 23-105-106-09 which is 2, 12 inch brake assemblies that can be mounted with a 4 or 5 inch bolt pattern. The 4 bolt pattern that is found on AL KO trailer axles like what you have now so it would be correct fit and would work great on a 5,200 lb axle. view full answer...
Yes, based on the distance between the welded on brackets of your camper the etrailer landing gear set part # RVLG-8HDL will fit on your 2021 Forest River Cherokee Wolf Pack. The motor normally used with this kit is the part # LC142178. If the motor you have looks like this (most likely it will) then it would work with this. view full answer...
For your 58" long arms, you're going to need the Replacement Idler Arm Assembly for Lippert Edge RV Awnings with LEDs # LC62ED for the Idler arm, and Replacement Drive Arm Assembly for Lippert Edge RV Awnings with LEDs # LC22ED for the drive arm. view full answer...
Yes, the Adco Olefin HD All-Climate + Wind RV Cover for 5th Wheel Toy Hauler # AD89ZR will work fine in north west Montana in the winter as this cover is designed to work in long term storage in all climates. view full answer...
I can certainly help you out with finding replacement parts for your Lippert Electric Landing Gear Set - Weld On - 37" Lift - 6,000 lbs # LC333964. The correct replacement motor for this setup is Lippert Venture 5th Wheel RV Landing Gear Motor # LC142178. This motor is rated for 5,000lbs on single motor 2 leg setup, and 8,000lbs on dual motor setup.
If you end up needing a replacement lead leg then you can go with Lippert Components 32" Lead Leg # LC179013, and for a replacement follow... view full answer...
I recommend the Furrion RV Tankless Water Heater - Gas - Automatic Pilot - 60,000 BTU - 16" x 16" Door # FR98SR. The unit itself is about 12 x 12 inches and the door is 16x16 so it will fit in your space and give you the door you need. view full answer...
What brand of landing gear do you have now? If it's Lippert, LCI, Venture, or Stromberg the part # LC196308 would be a higher rated motor for it that would work quicker but if you have something else let me know. view full answer...
You are correct that Curt does manufacture the Mopar factory 5th wheel hitches, so you can use either the # C16722 (12" diameter) or the # 16721 (10" factory lube plate) as a replacement. These are both 3/16" thick so they'll be suitable for almost any 5th wheel hitch, including your Mopar hitch. You'll want to measure the hitch's skid plate to determine which size will give you the most coverage. view full answer...
The MB Sturgis Sturgi-Stay T-Fitting part # 103613-MBS has type one fittings which are for smaller propane tanks like a 20 lb. The correct t-fitting for a larger 100 lb propane tank which will have POL fittings is the MB Sturgis Sturgi-Stay T-Fitting part # 103537-MBS.
I'm not sure exactly how you want to hook the tank up but I have attached for you below a list of all our hoses you can filter through by fitting type and length. If you need help with this, just let me know exactly how... view full answer...
The GH-8056-BRK you referenced is the Gen-Y Hitch Shock Absorbing 5th Wheel to Gooseneck Pin Box - Lippert Rhino - 30K GTW - 4.5K TW # GY53GR. This 5th wheel to gooseneck pin box has a Lippert Rhino bolt pattern is works best with 5th wheels that have a 2,500lbs - 4,500lbs pin weight. view full answer...
Disc brakes certainly work better than electric brakes, but before making that investment, I'd recommend doing some troubleshooting on your controller and the trailer brake system.
A properly functioning brake controller shouldn't have much problem braking that trailer, so let's begin by focusing on the trailer brakes themselves. Have you checked the brakes for adjustment? Were the trailer brakes broken in or burnished? Just because the travel trailer is new, I wouldn't assume that the... view full answer...
To connect to the POL fitting on your 100lb tank you'll need the MB Sturgis Propane Hose # 100022-144-MBS which has a male POL fitting and the MB Sturgis Disposable Propane Bottle Adapter Fitting # 204132-MBS which will connect to the 1"-20 fitting on the hose and to your green Type-1 fitting on your RV. view full answer...
Yes, the Air Lift WirelessAIR Compressor System for Air Helper Springs # AL74000EZ that you referenced does fit your 2022 Ford F-250 that has air bag suspension enhancement. This is only option that is both wireless and also gaugeless. view full answer...
For the LCI52-SB-86.5-68.5, the two ending measurements are:
1st - measurement from hub to hub, meaning the length of the axle in this case is 86.5 inches.
2nd - spring seat dimension where they're welded, meaning the spring seats are 68.5 inches apart.
It looks like this is a 5200-lb capacity axle. So, you would need a hub like part # AKHD-655-6-K. I've linked to a list of those hubs for you. Once you've determined your wheel size and bolt pattern, it will help you determine which hub... view full answer...
The Roadmaster Comfort Ride Shock Absorbers are going to offer better support for your trailer's leaf springs over the SumoSprings # TSS-107-40 you were looking at.
SumoSprings are great because they have a very soft to stiff progression so that you don't have a stiff ride when unloaded but because of this have a lower overall capacity than other options on the market.
The Comfort Ride shocks are going to be constantly fighting against bumps on the road to cancel out the chucking and... view full answer...
To choose the correct landing gear replacement for your 2021 Cherokee Wolfpack 365pack16 Toy Hauler you will first need to find the correct rated weight capacity. Your trailer has a listed GVWR of 16,825lbs. Since each landing gear will only be supporting a fraction of the weight you would be fine using with the combined 12,000lb capacity of the # UF17-943010 you referenced.
Next you would want to check the weld stop locations of your current landing gear posts and choose a landing gear... view full answer...
What it sounds like you're looking for is the Jack-It 2 Bike Rack for A-Frame Trailers # LC429756 which installs on the front of your trailer in-front of your propane tanks.
This rack will do essentially the same thing as what you're looking to do, and it will guarantee that you have enough room to remove and access your batteries since the rack won't even be near it.
If not, then we also have the Stromberg Carlson Bike Bunk Trailer-Mounted Bike Rack Carrier for A-Frame Trailers # CC-275... view full answer...
It is indeed the valve stem that gives you the psi rating for the wheels, and if you'd like you can go to a bolt-in valve stem rated for over 100 psi, the Americana Metal, Bolt-In Valve Stem # AM20906.
You can use this valve stem along with a 16" x 6" wheel with a 6 on 5-1/2" bolt pattern to get its complete 3,050 capacity, the Dexstar Steel Mini Mod Trailer Wheel - 16" x 6" Rim - 6 on 5-1/2 - Silver Powder Coat # AM20746.
Then, since you want a 14-ply tire, you'd have to go with a load... view full answer...
Go To Results